品牌：USB
USB31CET USB 3.1 USB (10 GT/s) Type-C Electrical Test Fixture Kit
USB31AET USB 3.1 USB (10 GT/s) Type-A and Micro-B Electrical Test Fixture Kit
QUADRAMAX USB Type-C™ and PD Tester
USBAUTH USB Type‐C Authentication Compliance Bridge
USBLSTD Low Speed Functional Compliance Test Device
USBFSTD Full Speed Functional Compliance Test Device
USB3ET USB 3.0 Electrical Test Fixture Kit
Low-speed Functional Compliance Test Device
The LS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators.
Please use product code USBLSTD to order.
Full-speed Functional Compliance Test Device
The FS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators.
Please use product code USBFSTD to order.
USB 3.0 xHCI-based PDK for SuperSpeed USB (Fresco Logic host)
Please use product code USB3PDK_FL to order the Fresco Logic host-side solution
USB 3.0 xHCI-based PDK for SuperSpeed USB (Renesas host)
Please use product code USB3PDK_REN to order the Renesas host-side solution
USB 3.0 Electrical Test Fixture Kit
The USB 3.0 Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY’s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals.
The kit contains five test fixtures and one 5-Volt DC power supply to provide V-Bus to peripherals. The fixtures consist of:
qty 2 – Host Test Fixtures
qty 2 – Device Test Fixtures
qty 1 – Device Calibration Fixture
qty 1 – Cable Assembly to be used in conjunction with the fixtures. Includes a USB 3.0 Standard A to Standard B (3 meter + 1 meter), Standard A to Standard B (4 inch) and Standard A to Micro B (4 inch).
The USB 3.0 Cable Kit provides five (5) SuperSpeed USB (USB 3.0) cables: The USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK) provides a host-side solution. It is intended to assist companies who are developing USB peripherals with the LPM feature. The USB 2.0 / 3.0 Drop-Droop fixtures assist companies in testing voltage drop and droop levels for hosts or hubs. The fixture is shipped with the cables for testing convenience only and are not mandatory for use in certification: qty (8) USB 3.0 1-meter cables + qty (1) USB 3.0 4-inch cable. A short, high quality cable assembly implementing 22AWG or larger power conductors should be used to minimize voltage drop across the cable. The over-current test fixture can be used to test and trigger current fault protection on a USB port by creating an over-current condition. The fixture is capable of drawing a variable load from 300mA to 1.8A and also includes a safety shut down to prevent overheating. The USB-IF test fixtures used for certifying signal quality of hi-speed hosts and peripherals. The fixtures eliminate the need for probes and require quality SMA cables for direct connection to the scope. The fixtures include USB cables but do not include SMA cables. The USB-IF does not sell or provide SMA cables and it is the vendor’s responsibility to obtain them. One recommendation for SMA cables includes the following: Agilent 15443A Matched Cable Pair (or equivalent).USB 3.0 Cable Kit
- Standard A to Standard B, 3 meter
- Standard A to Micro B, 1 meter
- Standard A to Standard B, 8 inch
- Standard A to Standard B, 4 inch
- Standard A to Micro B, 4 inchUSB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK)
USB 2.0 / 3.0 Drop-Droop Fixtures
Over-Current Test Fixture
USB 2.0 Hi-Speed Signal Quality Test Fixtures
Each test fixture set includes the following:
qty 1 - Device test Fixture
qty 1 - Host test fixture
qty 2 - Standard A to Standard B 1-meter cable
qty 1 - Standard A to Standard B short cable
qty 1 - Standard A to Micro B short cable